The Short Answer

The LXF-15H is a fully automatic ultrasonic woven label slitting machine. It is made for one job: slitting woven label rolls into narrow strips with a clean, sealed edge. Its vision system finds the slitting lines and moves the blades to the correct position automatically. The operator does not need to adjust the knives by hand. This solves the biggest problem with traditional ultrasonic slitting machines.

The Problem with Traditional Ultrasonic Slitting

During weaving, woven label tapes can vary slightly in width. The woven edge can move a little from roll to roll. On a traditional ultrasonic slitting machine, the operator has to keep checking the edge and readjusting the knives to keep the cut in the right place.

This causes several problems:

• The operator has to adjust the knives again and again.
• Strip width can change from roll to roll.
• Production depends on an experienced operator.
• High waste rate if the operator gets tired, and small errors become more likely.
• Changeover is slow when the next roll has a different width.

How the LXF-15H Solves It

The LXF-15H uses a vision system to read the slitting lines. It then moves the blades to the correct position automatically. This is vision-based automatic blade positioning.

The operator loads the roll and starts the machine. The machine feeds the material, keeps the tension stable, finds the slitting lines, and slits the roll into strips. There is no manual knife adjustment.

The result is a more stable strip width, a cleaner edge, and less dependence on an experienced operator. Changeover takes about 2–5 minutes. Compared with traditional ultrasonic slitting machines, one LXF-15H can deliver almost the output of two machines.

What It Slits

The LXF-15H is for woven labels only. It is an ultrasonic slitting machine, so the blade cuts and seals the edge at the same time. The sealed edge helps prevent fraying.

It is not a paper label slitter, a laser cutting machine, or a cut-and-fold machine. If you need to cut woven labels into individual shapes, that is a different CCD laser cutting machine.

Key Specifications

Model: LXF-15H
Machine type: fully automatic ultrasonic woven label slitting machine
Power: 300 W total
Voltage: 220 V single-phase
Speed: 5–20 m/min
Blade positioning accuracy: 0.2–0.5 mm
Minimum blade spacing: 8 mm
Vision range: 200 mm (L) × 350 mm (W)
Electrical cabinet: 600 × 300 × 700 mm
Main control cabinet: 500 × 230 × 350 mm
Machine weight: 86 kg
Changeover time: 2–5 minutes
Warranty: 1 year

What “Fully Automatic” Means

• Automatic feeding
• Automatic slitting
• Vision-based automatic blade positioning
• Stable tension control
• No manual knife adjustment during the run
• One machine output close to two traditional machines

Edge Quality

The ultrasonic blade cuts and seals the edge in one pass. The finished strip has a clean, sealed edge that helps prevent fraying. We test the actual woven label roll before confirming the machine configuration.

Who It Is For

• Woven label factories
• Woven label narrow fabric slitting workshops
• Label producers with many different roll widths
• Garment label factories that want to reduce dependence on experienced knife operators
• Production lines that need faster changeover and more consistent strip width

Want to see how the machine works?

Click here to watch the video of the fully automatic woven label ultrasonic slitting machine.

Frequently Asked Questions

Q: What does the vision system do?
A: It reads the slitting lines on the woven label roll and moves the blades to the correct position automatically.

Q: Does the operator need to adjust the knives by hand?
A: No. The LXF-15H uses vision-based automatic blade positioning. The operator does not manually adjust the knives during the run.

Q: What is the minimum blade spacing?
A: The minimum blade spacing is 8 mm.

Q: What is the blade positioning accuracy?
A: The blade positioning accuracy is 0.2–0.5 mm.

Q: What is the speed and changeover time?
A: The speed is 5–20 m/min, and changeover takes about 2–5 minutes.

Q: What materials can it slit?
A: It is for woven labels. It is an ultrasonic slitting machine that seals the edge; it is not for paper labels or other materials.

Q: Does it cut woven labels into individual shapes?
A: No. It slits rolls into narrow strips. For individual shapes, use a CCD laser cutting machine.

Q: What is the output compared with a traditional machine?
A: One LXF-15H can deliver almost the output of two traditional ultrasonic slitting machines.

Q: Do you provide installation?
A: The machine is plug-and-play, with online support. No installation is required. If you want our technician to visit your factory for installation and training, that service is available at an extra cost.

Q: What is the warranty?
A: 1 year.

Q: Can you test our woven label roll?
A: Yes. Send a piece of the actual roll, the target strip width, and the number of strips you need. We will test the slit and confirm the configuration.

Get a Quote

Send a piece of your woven label roll, the target strip width, the number of strips and your target output. We will confirm the LXF-15H configuration, test the slit, and quote the machine. Email us if you want machine photos and a running video.

Related Models

• Woven Label Slitting & Cutting Machines
• CCD Laser Woven Label Cutting Machine
• Woven Label Screen Printing Machine

Related Reading

• How to Choose a Woven Label Slitting or Cutting Machine